SHACMAN PARTS-Wheel bolt

Apr 11, 2026

Leave a message

 

Introduction of wheel bolts

  

info-1362-769

The wheel bolt is an important component used toconnect the hub and rim and realize torquetransmission between hub and rim. For the rear axleof heavy-duty truck, its function is to fix the wheelhub, wheel rim reducer, brake drum on the rear axlethrough wheel nuts, which can enable the wheel tocarry and transmit power.

 

The quality of wheel bolt

 

The quality of wheel bolts directly affects theperformance and safety of trucks. Often, the wheelbolt fracture is mainly caused by the looseness of thewheel nut. The form of bolt fracture is mostly fatiguefracture, and the cause of fatigue fracture is alsomostly the insufficient preload of the bolt, whichleads to the excessive external variable load on the bolt, resulting in fatigue tracture.

  • The quality of the bolt itself depends on thematerial, forging, machining accuracy and theprocess parameter control of heat treatment.
  • Material: material is the prerequisite todetermine the quality of the bolt itself. A goodmaterial should have a stable and qualified elementcomposition ratio, and can achieve excellentmechanical properties after heat treatment.
  • Forging: during the forging process, stricttemperature control and heating area control areimportant factors to avoid early abnormal fracture ofbolts.
  • Machining accuracy: the fitting accuracy of thethread pair affects the service life of the product. Ifthe fit clearance of the thread pair is too large, theguaranteed load of the thread will be greatlyreduced, and even out of function before use.
  • Heat treatment: the quenching and temperingprocess is the key to the realization of themechanical properties of bolts. Strictly control thetemperature, time and cooling medium of eachprocess, so as to meet the performance graderequirements of all kinds of bolts and make therigidity and toughness of products meet the userequirements of actual working conditions.

 

Advantages and disadvantages
of wheel bolt

 

  • Higher bolt hardness does not mean better bolt quality.High hardnessmeans good rigidity of the product only, but nothing to do with good toughness. Good bolts need to meet the two-way requirements of rigidity and toughness. Bolts with insufficient rigidity cannot be tightened, and the plastic deformation trend is obvious until they are stretched and broken; The bolt with insufticient toughness cannot meet the radial load, and brittle fracture occurs after the bolt is subjected to shear force. Only good materials undergo strict heat treatment can meet the rigidity and toughness of bolts and maximize the service life of products;
  • Common bolt surface treatments include oxidation, phosphating, galvanizing, electroless nickel plating (commonly known as tempering and replacement in market). As different methods of surface treatment, their purpose is to
    meet the rust prevention and appearance requirements of products which do nothing in in strengthening the performance of products themselves. On the contrary, if the later "dehydrogenation" process of galvanized and nickel plated bolts is not done well, the bolts will be delayed to fracture due to "hydrogen embrittlement";
  • After loosening the threaded fasteners, great kinetic energy will be generated due to impact. These kinetic energy will directly act on the radial direction of the bolt, which will cause the early abnormal shear fracture of the bolt. Therefore, the tightening torque of the bolt should be guaranteed. At the same time, how to prevent loosening is also the key to prolong the service life of the product.

 

Example of quality comparison

 

info-362-511
Factory parts
● Material:35CRMO(Structural steelgrade) 
    ● Bolt marking:10.9(Rockwell hardness32-39)
                     ● Measured Rockwell hardness:38.5
            ● Process: the production process is cold heading wire rolling, heat treatment(quenching and tempering   treatment),surface galvanizing treatment, and thebolt root adopts plane interference fit,which can effectively alleviate thedeformation of the hub hole afterreplacing the bolt.
info-378-513
 
Counterfeit part
● Material:40CR(Standard steel grade)
            ● Bolt marking:12.9(Rockwell hardness39-44)
                         ●  Measured Rockwell hardness: 38.5
                         ● Process: the knurled structure isadopted at the                            root of the bolt. Thismechanism will damage the holediameter of the hub, resulting in thehole diameter becoming larger, and thegenuine bolts can no longer be used.

Reasons for the adoption of root knurling in counterfeit parts: Replace the counterfeit parts after the truck has been operated for one year. At this time, there is a slight deformation in the wheel hub hole, so the way of increasing the pressure on the root is used to prevent the bolt from loosening, but knurling will further damage the wheel hub hole diameter and the truck is unable to use the genuine bolts any more.

 

Common wheel bolts of SHACMAN

 

Type Specs Structure of brake
Drum Disk
Front axle 7.5T H150A2289BZF3 HD90009410112
9.5T H150A2289BZF3 DZ9100410134
5.5T H150A2287AZF3 H150A2269AZF3
4.8T H150A2279AZF3 H150A2269AZF3
Drive axle Single reduction H150A22105AZF3 H150A22105AZF3
Single reduction H150A22105AZF3 H150A22109BZF3
Double reduction H150A22120BZF3 H150A2299AZF3
Double reduction H150A22125BZF3 /

 

 

 

info-433-197
H150A2289BZF3-PT-01
Wheel bolt with nut
M22X1.5  L=89mm
info-513-240

 

H150A2287AZF3
Wheel bolt
M22x1.5  L=87mm

 

info-514-240

 

H150A2299AZF3-PT
Wheel bolt with nut
M22x1.5  L=99mm

 

info-512-240

 

H150A2269AZF3-PT
Wheel bolt with nut
M22X1.5 L=69mm

 

info-514-240

 

H150A22120BZF3
Wheel bolt
M22x1.5  L=120mm

 

info-507-242

 

H150A22105AZF3
Nheel bolt
M22x1.5  L=105mm

 

info-605-186

 

H150A22125BZF3
Wheel bolt
M22X1.5  L=125mm

 

 

 

 

 

 

 

Send Inquiry